Minibots

From Deep Blue Robotics Wiki
Revision as of 23:02, 12 December 2016 by Estroh (Talk | contribs)

Jump to: navigation, search

Purpose

Running Events

LiPo Battery Charging Notes:

LiPo batteries are generally safer and more environmentally friendly than other R/C batteries like NiCd and NiMH. LiPo batteries have become the most common high performance R/C battery. However, if charged, discharged, stored, maintained, or handled improperly, they can become extremely dangerous. When maintained carefully LiPo batteries are very reliable and will last a very long time. As such the following instructions should be followed very closely LiPo batteries are lightweight and very effective but have the same problems as other lithium-ion cells. This means that overcharge, over-discharge, over-temperature, short circuit, crush and nail penetration may all result in a catastrophic failure, including the pouch rupturing, the electrolyte leaking, and fire. If you notice that the battery is damaged or puffed up (expanded), do not use or charge. Bring the battery to Leadership, Mentor, or Teacher to review and determine what to do with the battery. LiPo Fire: A LiPo fire is a chemical fire. Always keep a Class D fire extinguisher nearby your battery charging/discharging and storage area. The battery charging/discharging and storage area should be free from any materials which can catch fire such as wood tables, carpet, or gasoline containers. The ideal surface for charging and storing LiPo batteries is concrete or ceramic. Charging: NEVER LEAVE BATTERIES UNSUPERVISED WHEN CHARGING Charge the battery after every use as this will extend the lifecycle of the battery. Additionally, if the battery voltage gets too low it will not be able to be recharged. The battery charging/discharging and storage area should be free from any materials which can catch fire such as wood tables, carpet, or gasoline containers. The ideal surface for charging and storing LiPo batteries is concrete or ceramic. Hook up the battery to the charger and plug in the balance plug Make sure charger settings are set correctly Battery Type: LiPo Charge Type: Balance Cells: 2*

  • Initial batteries that have been purchased for the Combat Robotics outreach program. May change in the future

NOTE: If you get a Low Voltage Error bring the battery to Leadership, Mentor, or Teacher to review and use the special instructions below:



Storage: LiPo batteries should always be stored and transported in a metal ammo box to protect against damage and for fire suppression. Do not allow batteries to be stored in direct sunlight for an extended period of time. Always store your LiPo batteries at room temperature. Do not store them in a hot garage, or in a cold refrigerator. Even though a cold battery has less chemical reaction taking place which can prolong its lifespan, taking a battery out from a cold fridge can cause condensation to occur on the inside of the battery, which can be very dangerous. Never leave your LiPo batteries sitting around on a full charge for more than 2-3 days. If by the 3rd day you realize you are not going to use your battery today, you need to discharge your battery down to 3.6v-3.8v per cell for safe storage until you are ready to use the battery again. Special Instructions for recovering a LiPo battery that has been NOTE: These instructions need to be followed exactly as the potential for damage, fire or battery explosion are higher if not followed exactly. DO NOT LEAVE THE BATTERY OR CHARGER UNATTENDED when following the Special Instructions ONLY AUTHORIZED AND TRAINED LEADERSHIP, MENTORS OR TEACHER should perform the activities below: Hook up battery to the charger but do not plug in the balance plug Place the battery in the charging bag and close the Velcro top Set the charger to the following: Battery Type: NiMh Charge Type: Charge Voltage: 0.01 or lowest setting Under constant supervision start the charge process and stop the charge process when the total voltage reaches 3Volts times the # of cells. For 2 Cell LiPo batteries this will equal 6 Volts (3 Volts times 2 cells = 6 Volts) Stop the charge process and follow normal instructions above. Ensure the settings are set back to LiPo.